1. 2014
  2. Modeling the crystallographic changes in processing of Al alloys

    Sidor, JJ., Petrov, RH. & Kestens, LAI., 2014, In : Journal of Materials Science. 49, 9, p. 3529-3540 12 p.

    Research output: Contribution to journalArticleScientificpeer-review

  3. Orientation dependence of the martensite transformation in a quenched and partitioned steel subjected to uniaxial tension

    de Knijf, D., Nguyen Minh, T., Petrov, RH., Kestens, LAI. & Jonas, JJ., 2014, In : Journal of Applied Crystallography. 47, 4, p. 1261-1266 6 p.

    Research output: Contribution to journalArticleScientificpeer-review

  4. Three-dimensional EBSD characterization of thermo-mechanical fatigue crack morphology in compacted graphite iron

    Pirgazi, H., Ghodrat, S. & Kestens, LAI., 2014, In : Materials Characterization. 90, p. 13-20 8 p.

    Research output: Contribution to journalArticleScientificpeer-review

  5. Warm deep-drawing and post drawing analysis of two Al-Mg-Si alloys

    Ghosh, M., Miroux, A., Werkhoven, RJ., Bolt, PJ. & Kestens, LAI., 2014, In : Journal of Materials Processing Technology. 214, 4, p. 756-766 11 p.

    Research output: Contribution to journalArticleScientificpeer-review

  6. 2013
  7. An infrared spectroscopic study of sodium silicate adsorption on porous anodic alumina

    Gaggiano, R., de Graeve, I., Mol, JMC., Verbeken, K., Kestens, LAI. & Terryn, HA., 2013, In : Surface and Interface Analysis. 45, p. 1098-1104 7 p.

    Research output: Contribution to journalArticleScientificpeer-review

  8. Austenite stability study by micro-tensile testing of Q&P steel.

    Knijff, D., Petrov, RH., Föjer, C. & Kestens, LAI., 2013, Proceedings of the International Symposium on New Developments in Advanced High-Strength Sheet Steels.. Hickey, KD. & Ashburn, RE. (eds.). Vail, Colorado, USA: AIST, p. 185-195 11 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  9. Automatic meshing method for optimization of the fusion zone dimensions in finite element models of welds

    Decroos, K., Ohms, C., Petrov, RH., Seefeldt, M., Verhaeghe, F. & Kestens, LAI., 2013, Proceedings International Conference on Residual Stresses 9. Kurz, S. J. B., Mittemeijer, E. J. & Scholtes, B. (eds.). Pfaffikon, Switzerland: Trans Tech Publications, p. 597-604 8 p. (Materials Science Forum; vol. 768-769).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  10. Evolution of the microstructural surface characteristics during annealing.

    Gomes, E., Verbeken, K., Gautam, JP. & Kestens, LAI., 2013, In : Materials Science and Engineering A: Structural Materials: Properties, Microstructures and Processing. 561, p. 312-316 5 p.

    Research output: Contribution to journalArticleScientificpeer-review

  11. Influence of finishing rolling variables on the austenite recrystallization and grain growth.

    Carretero Olalla, V., Sanchez Mouriño, N., Thibaux, P., Kestens, LAI. & Petrov, RH., 2013, In : Materials Science Forum. 753, p. 439-443 5 p.

    Research output: Contribution to journalArticleScientificpeer-review

  12. Measurement and characterization of thermo-mechanical fatigue in compacted graphite iron.

    Ghodrat, S., Riemslag, AC., Janssen, M., Sietsma, J. & Kestens, LAI., 2013, In : International Journal of Fatigue. 48, p. 319-329 11 p.

    Research output: Contribution to journalArticleScientificpeer-review

Previous 12 3 4 5 6 7 8 9 ...19 Next

ID: 157832