1. Article › Scientific › Not peer-reviewed
  2. Delamination Analysis of Cu/low-k Technology Subjected to Chemical-Mechanical Polishing Process Conditions

    Yuan, CA., van Driel, WD., van Silfhout, RBR., van der Sluis, O., Engelen, RAB., Ernst, LJ., van Keulen, F. & Zhang, GQ., 2006, In : Microelectronics Reliability. 46, p. 1679-1684 6 p.

    Research output: Contribution to journalArticleScientific

  3. Hysteresis and time-dependent constitutive modelling of filled vulcanised rubber

    Ernst, LJ. & Septanika, EG., 1999, In : The European Physical Journal. Special Topics. 9, p. 63-72 10 p.

    Research output: Contribution to journalArticleScientific

  4. On the analysis of the interlaminar strain-energy release rates in ring-fracture specimens

    Rizov, V. & Ernst, LJ., 2001, In : Composite Structures. 54, p. 331-334 4 p.

    Research output: Contribution to journalArticleScientific

  5. Vertical die crack stresses of Flip Chip induced in major package assembly processes

    Yang, DG., Ernst, LJ., van t Hof, C., Kiasat, MS. & et al, ., 2000, In : Microelectronics Reliability. 40, p. 1533-1538 6 p.

    Research output: Contribution to journalArticleScientific

  6. Article › Scientific › Peer-reviewed
  7. A Micromechanics-Based Vapor Pressure Model in Electronic Packages

    Fan, XJ., Zhou, J., Zhang, GQ. & Ernst, LJ., 2005, In : Journal of Electronic Packaging. 127, p. 262-267 6 p.

    Research output: Contribution to journalArticleScientificpeer-review

  8. A fast moisture sensitivity level qualification method

    Ma, X., Jansen, KMB., Zhang, GQ., van Driel, WD., van der Sluis, O., Ernst, LJ., Regards, C., Gautier, C. & Frémont, H., 2010, In : Microelectronics Reliability. 50, 2010, p. 1654-1660 7 p.

    Research output: Contribution to journalArticleScientificpeer-review

  9. A model for determining crack opening stress intensity factor ratio under tri-axial stress state

    He, YT., Li, F., Shi, R., Zhang, GQ., Ernst, LJ. & Fu, XJ., 2005, In : Key Engineering Materials. 297-300, p. 1572-1578 7 p.

    Research output: Contribution to journalArticleScientificpeer-review

  10. A new ultimate strength model of notched composite laminates - including the effects of matrix failure

    Liu, CJ., Nijhof, AHJ., Ernst, LJ. & Marissen, R., 2009, In : Journal of Composite Materials. 44, 11, p. 1335-1349 15 p.

    Research output: Contribution to journalArticleScientificpeer-review

  11. An automatic and interactive large-deformation measurement system based on image processing

    Septanika, EG., Ernst, LJ. & van den Hooff, LACM., 1998, In : Experimental Mechanics. 18, 3, p. 181-188 8 p.

    Research output: Contribution to journalArticleScientificpeer-review

  12. Analytical estimate for curing-induced stress and warpage in coating layers

    Jansen, KMB., de Vreugd, J. & Ernst, LJ., 2012, In : Journal of Applied Polymer Science. 126, 5, p. 1623-1630 8 p.

    Research output: Contribution to journalArticleScientificpeer-review

Previous 1 2 3 4 5 6 7 8 ...25 Next

ID: 160678